{"id":8759,"date":"2025-01-22T17:12:28","date_gmt":"2025-01-22T22:12:28","guid":{"rendered":"https:\/\/www.inthacity.com\/blog\/uncategorized\/stop-using-dangerous-table-saw-accessories-dewalt-bosch-brands-to-avoid\/"},"modified":"2025-08-23T19:54:04","modified_gmt":"2025-08-24T00:54:04","slug":"stop-using-dangerous-table-saw-accessories-dewalt-bosch-brands-to-avoid","status":"publish","type":"post","link":"https:\/\/www.inthacity.com\/blog\/life\/crafts\/woodworking\/stop-using-dangerous-table-saw-accessories-dewalt-bosch-brands-to-avoid\/","title":{"rendered":"Stop Using These Dangerous Table Saw Accessories Immediately \u2013 DeWalt, Bosch, and More Brands to Avoid"},"content":{"rendered":"

We\u2019ve all had those moments\u2014those dumb ideas<\/em> that seem brilliant at the time but later make us cringe. For James Hamilton, the mastermind behind the Stumpy Nubs YouTube channel<\/a>, one such idea was designing a rocking chair that rocked side to side. But as he explains in his latest video, some ideas aren\u2019t just dumb\u2014they\u2019re downright dangerous. Today, we\u2019re diving into one of those ideas: standing on the wrong side of a table saw. Spoiler alert: it\u2019s a disaster waiting to happen.<\/p>\n

Before you roll your eyes and say, \u201cThe internet is full of bad ideas, why should I care about this one?\u201d let me stop you right there. This particular idea has been suggested in the comments of Stumpy Nubs\u2019 videos multiple times<\/em>, including twice just last week. And while the people suggesting it might not be dumb (they probably just don\u2019t use table saws often), the idea itself is a recipe for disaster. So, let\u2019s break it down and see why this is one of the worst woodworking hacks you could ever try.<\/p>\n

The Two Worst Table Saw Ideas You\u2019ll Ever Hear<\/h2>\n

According to Stumpy Nubs, there are two shockingly common suggestions for avoiding table saw kickback\u2014both of which are terrible. The first is standing on the opposite side of the fence<\/em>, and the second is standing on the opposite side of the table saw<\/em> and pulling the workpiece toward you. Let\u2019s tackle the second one first because, honestly, it\u2019s the one that makes me cringe the most.<\/p>\n

1. Pulling the Workpiece Toward You: A Disaster in the Making<\/h3>\n

Imagine this: you\u2019re standing on the opposite side of the table saw, pulling the workpiece toward you. Sounds harmless, right? Wrong. Here\u2019s why. When you make a rip cut<\/a>, you\u2019re not just pushing the wood forward\u2014you\u2019re also applying lateral pressure to keep it against the fence. This lateral pressure is crucial for a clean, safe cut. But if you\u2019re pulling the wood toward you, how do you apply that pressure? You\u2019d have to lean over the blade, reaching around it to guide the wood. Does that sound safe to you? Spoiler: it\u2019s not.<\/p>\n

Some folks suggest using a featherboard to eliminate the need for lateral pressure and a hooking device to pull the wood through. Sounds good in theory, but in practice? Not so much. Longer workpieces would hang off the opposite side of the saw, making it nearly impossible to guide them properly. And forget about cutting plywood panels\u2014you\u2019d need telescopic arms to pull that off. If a kickback were to occur, you\u2019d be at a much higher risk of pulling your hands into the blade. Yikes.<\/p>\n

2. Standing on the Opposite Side of the Fence: Just as Bad<\/h3>\n

Now, let\u2019s talk about the second bad idea: standing on the opposite side of the fence. Some people swear this is the \u201cproper\u201d way to make a cut<\/a>, but Stumpy Nubs begs to differ. Why? Because it\u2019s awkward, unstable, and downright dangerous. Applying lateral pressure from the opposite side of the fence requires you to lean over the saw<\/a>, which is not only uncomfortable but also increases the risk of losing control. And if you\u2019re cutting a wide board? Forget it\u2014you\u2019d be leaning so far over, you might as well be doing yoga on the table saw.<\/p>\n

Again, some suggest using a featherboard to apply lateral pressure while you push the workpiece forward. But this only works with small pieces. Longer boards require a two-handed feed, and plywood? Forget about it. It\u2019s just not practical.<\/p>\n

The Real Solution: Use Your Blade Guard<\/h2>\n

So, what\u2019s the solution to avoiding<\/a> kickback? It\u2019s simple: use your blade guard. Most blade guards come with a built-in splitter that prevents the wood from pinching or wedging against the blade, which is the primary cause of kickback. If you don\u2019t have a blade guard (or you\u2019re one of those people who refuses to use one), a riving knife or even a homemade splitter can provide similar protection.<\/p>\n

And if you\u2019re still worried about getting hit by a flying piece of wood, you can position your body out of the direct path of the blade without changing the side of the saw or the fence. Table saws can be safe and valuable tools\u2014if you use them properly.<\/p>\n

A Game-Changing Wood Finish: Clean Armor<\/h2>\n

Now, let\u2019s shift gears and talk about something exciting: Clean Armor<\/a>, a new wood finish that Stumpy Nubs is raving about. This stuff is a game-changer. It goes on easily, contains no harmful VOCs, and fully cures in just two minutes with the help of a UV light. Plus, it offers incredible protection\u2014even against harsh chemicals like acetone. If you\u2019re looking for a finish that\u2019s as durable as it is easy to use, Clean Armor is worth checking out.<\/p>\n

Watch the Original Video<\/h2>\n

If you want to see Stumpy Nubs break down these bad ideas in action, check out the original video below:<\/p>\n\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t
\n\t\t\t\t\t\t\t
<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t
<\/div>\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\n\t\t\t\t\t
\nPrev<\/a>\n1<\/span> of<\/span> 1<\/span>\nNext<\/a>\n<\/div>\n
\n\t