- \n
- Router table<\/li>\n
- Roundover bits (various sizes)<\/li>\n
- Push blocks<\/li>\n
- Scrap wood<\/li>\n
- Drill (for sanding)<\/li>\n
- Sandpaper<\/li>\n<\/ul>\n
Step 1: Prepare Your Wood Blanks<\/h2>\n
Start by ripping your scrap wood into rectangular blanks. The width of the blank should match the diameter of the dowel you want to create. For example, if you need a 1-inch dowel, rip a 1-inch-wide blank.<\/p>\n
Step 2: Choose the Right Roundover Bit<\/h2>\n
Roundover bits are measured by the radius they cut, which is half the diameter of the dowel. For a 1-inch dowel, use a \u00bd-inch roundover bit. For a \u00bd-inch dowel, use a \u00bc-inch roundover bit, and so on.<\/p>\n
Step 3: Set Up Your Router Table<\/h2>\n
- \n
- Adjust the Bit Height<\/strong>: Set the roundover bit so the lower end of the cutter is flush with the top of the router table. You can test this by feeling for when the wood no longer catches on the cutter.<\/li>\n
- Set the Fence<\/strong>: Position the fence flush with the top of the bit\u2019s cutter. Using a fence instead of the guide bearing on the bit itself makes it easier to control long dowel blanks.<\/li>\n<\/ol>\n
Step 4: Shape the Dowel<\/h2>\n
A roundover bit removes material gradually, so you can take four full-depth passes to shape your dowel. Here\u2019s how:<\/p>\n
- \n
- First Three Passes<\/strong>: Begin about an inch from the leading end of the blank and stop before reaching the trailing end. This leaves uncut rectangular sections at both ends, which prevents the dowel from rolling and ensures consistent results.<\/li>\n
- Fourth Pass<\/strong>: Complete the final pass, ensuring the dowel doesn\u2019t roll. If the dowel is too long for your router table, consider using an extension or support to keep it stable.<\/li>\n<\/ol>\n
Step 5: Sand the Dowel<\/h2>\n
Most router bits leave a smooth surface, but if you need to remove flat spots or cut marks, you can sand the dowel:<\/p>\n
- \n
- Small Dowels<\/strong>: Chuck them into a drill and sand while spinning.<\/li>\n
- Large Dowels<\/strong>: Use a lag screw and socket to spin them in the drill. For extra support, drive a nail through a scrap of wood to act as a center point, mimicking a lathe.<\/li>\n<\/ul>\n
After power sanding, finish by hand sanding along the grain to remove any radial scratches.<\/p>\n
Tips for Success<\/h2>\n
- \n
- Always use push blocks to keep your hands safe from the router bit.<\/li>\n
- For longer dowels, ensure your router table has adequate support or use an extension.<\/li>\n
- Test your setup on a scrap piece before cutting your actual dowel.<\/li>\n<\/ul>\n
Final Thoughts<\/h2>\n
Making your own dowels is a simple and rewarding process that allows you to customize your woodworking projects. By following this method, you\u2019ll no longer be limited by the inconsistent selection at hardware stores. Plus, you\u2019ll save money<\/a> and make use of scrap wood.<\/p>\n
For a visual guide, check out the original video by Stumpy Nubs (James Hamilton)<\/strong> below:<\/p>\n\t\t\t
\n\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\n\t\t\t\t\t\nPrev<\/a>\n1<\/span> of<\/span> 1<\/span>\nNext<\/a>\n<\/div>\n\n\t- \n\t\t\t\t\t
- \n\t\t\t\t\t\t\t\t\n\t\t\t\t\t\n\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t
![\"hqdefault](\"https:\/\/i.ytimg.com\/vi\/YAY8wGPVG8w\/hqdefault.jpg\" "\\"\\"")
\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\tStop buying these from stores! (Make them instead)<\/h3>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
<\/div>\n\t\t\t\t\t\t\t\t\t<\/a>\n\t\t\t\t\t\t\t<\/li>\n\t\t\t\t\n\t\t\t\t<\/ul>\n<\/div>\nPrev<\/a>\n1<\/span> of<\/span> 1<\/span>\nNext<\/a>\n<\/div>\n\t\t\t\t<\/div>\n\t\t\t<\/div>\n\t\t\t\nAnd don\u2019t forget to protect your hearing while working in the shop! Consider using ISOtunes Bluetooth earbuds<\/strong> for hearing protection and entertainment. Support small businesses and enhance your woodworking experience by checking out the link below the video.<\/p>\n
Happy woodworking!<\/p>\n
Wait!<\/strong> There's more...check out our gripping short story that continues the journey:\u00a0Elysium Drift<\/a><\/p>\n
- \n\t\t\t\t\t\t\t\t\n\t\t\t\t\t
- Large Dowels<\/strong>: Use a lag screw and socket to spin them in the drill. For extra support, drive a nail through a scrap of wood to act as a center point, mimicking a lathe.<\/li>\n<\/ul>\n
- Fourth Pass<\/strong>: Complete the final pass, ensuring the dowel doesn\u2019t roll. If the dowel is too long for your router table, consider using an extension or support to keep it stable.<\/li>\n<\/ol>\n
- Set the Fence<\/strong>: Position the fence flush with the top of the bit\u2019s cutter. Using a fence instead of the guide bearing on the bit itself makes it easier to control long dowel blanks.<\/li>\n<\/ol>\n
- Adjust the Bit Height<\/strong>: Set the roundover bit so the lower end of the cutter is flush with the top of the router table. You can test this by feeling for when the wood no longer catches on the cutter.<\/li>\n
![\"story_1737678789_file](\"https:\/\/www.inthacity.com\/blog\/wp-content\/uploads\/2025\/01\/story_1737678789_file.jpeg\" "\\"\\"")
<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"